VAL Avionics NAV 2000 Guía de instalación Pagina 259
- Pagina / 401
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SkyView System Installation Guide - Revision R 14-1
14. SV-ADSB-470 Installation, Configuration, and Testing
SkyView can receive traffic and weather via the SV-ADSB-470 UAT Band Traffic and Weather
Receiver. The SV-ADSB-470 is a remote mounted module that connects to SkyView via a serial
port on your SkyView display(s). It also requires the installation of a dedicated antenna for ADS-
B signal reception.
A map license is required to display ADS-B traffic and weather data received from
the SV-ADSB-470. A trial map license for the initial 30 flight hours is included with
every SkyView display. After the 30 flight hour trial expires, installation of the SV-
MAP-270 Navigation Mapping Software License is required to display ADS-B traffic
and weather data.
Read and understand the System Planning Chapter before installing the SV-ADSB-
470.
The SV-ADSB-470 receives traffic and weather via the 978 MHz UAT ADS-B
frequencies, which are only utilized in the US. Therefore, traffic and weather are
only available in the US. Dynon Avionics does not recommend the use of the SV-
ADSB-470 outside the US.
Although weather and TFR information (FIS-B services) available any time the SV-
ADSB-470 is in an ADS-B ground station coverage area, ADS-B FIS-B traffic is only
available if a transponder with ADS-B OUT capability is installed and is providing
ADS-B OUT position reports into the ADS-B system.
To enable ADS-B Traffic information on the SV-ADSB-470 with an ADS-B OUT
device other than the Dynon Avionics SV-XPNDR-261/262:
1. SETUP MENU > SYSTEM SETUP > AIRCRAFT INFORMATION > AIRCRAFT HEX
CODE > (enter the HEX Code assigned to your aircraft) > ACCEPT (button)
2. SETUP MENU > SYSTEM SETUP > TRAFFIC SETUP > NON-DYNON ADS-B OUT
ONBOARD > YES
Only ADS-B OUT devices that comply with TSO C166b or later of the ADS-B spec
will allow traffic to be displayed properly. The ADS-B OUT device must be set up to
tell the ADS-B system that the aircraft is receiving on 978 MHz.
Figure 88 has a high-level overview of a suggested SV-ADSB-470 installation, configuration, and
testing procedures:
- SkyView 1
- Contact Information 3
- Copyright 3
- Limited Warranty 3
- Revision History 4
- Calibration Section 5
- Table of Contents 13
- Table of Contents 15
- 1. Introduction 19
- Warning 19
- About this Guide 20
- Getting Started 20
- 2. System Planning 23
- Power Consumption 24
- Includes SV52, SV52C, SV52L 25
- Temperature Specifications 26
- Location Requirements 28
- SV-EMS-220/221 31
- SV-GPS-250 31
- SV-XPNDR-261/262 32
- SV-BAT-320 32
- SV-ARINC-429 33
- SV-ADSB-470 33
- Mounting Requirements 34
- SkyView System Construction 34
- SkyView Network Hub 35
- Test SkyView Network Cable 36
- Ethernet Connection 36
- Example SkyView Systems 38
- HSI Requirements 41
- Screen Synchronization 43
- Display Bezel Layout 44
- Operation Basics 45
- SkyView Touch 47
- Menu Navigation 47
- How to Reboot the Display 49
- How to Enter the Setup Menus 49
- Screens and Menus 50
- Message Notification Area 51
- In Flight Setup Menu 51
- Setup Menu 51
- System Software Menu 52
- System Setup Menu 52
- LOCAL DISPLAY SETUP Menu 53
- PFD SETUP Menu 54
- EMS Setup Menu 55
- MAP Setup Menu 55
- Autopilot Setup Menu 55
- Transponder Setup Menu 56
- Hardware Calibration Menu 56
- How to Update Firmware 57
- How to Load and Delete Files 59
- Figure 19–SV-D700 Dimensions 65
- SkyView Network Connectors 68
- Network Setup and Status 68
- Internal Time Keeping 71
- Serial Devices 71
- Table 10–Icarus Format 76
- USB Usage and Accessibility 82
- Display Setup 84
- Serial Port Configuration 85
- Brightness Setup 87
- Top Bar Setup 88
- Aircraft Information 88
- Screen Layout Setup 89
- Touch Setup 90
- Pneumatic Ports 94
- Magnetic Heading Calibration 94
- Probe Location 95
- PFD-Related Settings 97
- Airspeed Limitations 98
- Vertical Speed Scale 99
- G Meter 99
- Synthetic Vision License 99
- Other ADAHRS Calibrations 100
- License Information 103
- Databases 104
- Terrain Data 105
- Aviation/Obstacle Databases 106
- Charts and Airport Diagrams 107
- Removing Databases 108
- Base map and Cultural Data 108
- Loading Databases 108
- Physical Installation 111
- SkyView Network Connection 112
- Table 12–EMS Wire Harnesses 113
- P/N 456180: 20mA 119
- 456180) 132
- P/N 456180 only) 132
- Tools and Equipment Required 141
- Voltmeter Inputs 142
- Tachometer 144
- Figure 31–Magneto Pick Off 145
- Manifold Pressure Sensor 147
- Oil Pressure Sensor 148
- Oil Temperature Sensor 150
- Fuel Pressure Sensor 151
- 1/8-27 NPT 152
- 0-30 PSI 152
- 0-80 PSI 152
- Fuel Flow Sensor 154
- Fuel Level Sensor 156
- Ammeter Shunt 158
- Rotax CHT Sensors 161
- Coolant Pressure Sensor 163
- Coolant Temperature Sensor 164
- Contacts 165
- General Purpose Thermocouple 166
- External EMS Warning Light 167
- Engine Information 167
- Rotax 912 Behavior 168
- EMS Sensor Definitions 169
- EMS Sensor Input Mapping 169
- Table 39–Example Sensor Map 170
- EMS Sensor Settings 171
- Example Voltmeter Setup 175
- Example Contact Sensor Setup 176
- Example RPM Setup 177
- Figure 49–Anatomy of a 178
- Widget: Oil 178
- Temperature 178
- EMS Screen Layout Editor 179
- EMS Sensor Calibration 181
- Serial Connection 185
- Configuration 187
- 9. SV-BAT-320 Installation 189
- Electrical Connection 191
- Battery Charging 191
- Battery Status Icon 191
- Test Procedure 193
- Dynon Autopilot Servo Models 196
- Additional Resources 196
- Push-Pull Servo Dimensions 199
- Figure 60 - Shear Screw 201
- Kit Contents 206
- Servo Calibration Procedure 210
- Servo Test Procedure 211
- Autopilot Setup Options 211
- Roll Axis Configuration 212
- Pitch Axis Configuration 213
- Disengage Button Options 216
- Installation Instructions 221
- Electrical Connections 222
- Power/Ground Input 226
- Pin 1/2 and 12/13 Loopbacks 227
- Serial RX/TX 227
- Antenna Installation 229
- Antenna Ground Plane 230
- Antenna Cable 230
- Antenna TNC Connector 232
- Serial Port Setup 232
- Transponder Settings 233
- Altitude Encoder Calibration 236
- Post Installation Checks 237
- Transponder Software Updates 237
- ARINC-429 Device Connection 242
- SV-ARINC-429 Pinout 243
- ARINC Device Connections 245
- Serial Port Connection 254
- VP-X Settings 255
- Figure 87 - VP-X Example 257
- Electrical Installation 261
- Antenna BNC Connector 265
- Failure Warning 270
- Tools and Materials Required 270
- AOA/Pitot Probe Mounting 276
- AOA/Pitot Probe Dimensions 277
- Plumbing 278
- Pressure Check 278
- Calibration 279
- Tools and Equipment 280
- Transponder Wiring 280
- Installation 285
- Setup Configuration 285
- Checkout and Operation 285
- SV-COM-PANEL Dimensions 288
- Optional Flip / Flop Button 301
- Certification Considerations 308
- SV-AP-PANEL Installation 333
- Network Setup 334
- Taking a Screenshot 341
- Operational Status 344
- Display Serial Number 345
- Display Firmware Version 345
- Display Input Voltage 345
- Annual Backup Battery Test 347
- Troubleshooting 348
- Compass Calibration Fails 349
- Display does not Turn On 349
- SkyView Equipment Weights 351
- SV-XPNDR-261 Specifications 354
- SV-XPNDR-262 Specifications 355
- Wire Gauge 359
- Grounding 359
- Wire Insulation 360
- Wire Size 360
- Twisted Pairs 360
- SV-BAT-320 Connection 362
- OAT Connection 362
- Servo Harness Pin-Out 364
- SkyView D37 Harness Pin-Out 365
- SkyView D37 Block Diagram 366
- SV-EMS-220/221 Pin-Out 368
- 456180 only) sensor power 370
- SV-ARINC-429 Pin-Out 372
- SV-ADSB-470 Pin-out 373
- SV-XPNDR-261/262 Pin-Out 373
- ADS-B Parameters Supported 376
- FAA 91.227 Compliance 377
- AMC 20-24 Compliance 378
- DYNON EMS Serial Data Format 389
- GP Inputs 392
- NMEA OUT Serial Data Formats 394
- NMEA OUT ( FULL) 395
- User Data Log 397
- Recent Flight Data Log 398
- Alert Data Log 398
- Exporting Data Logs 399
© 2020, manymanuals.es. Todos los derechos reservados | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales