VAL Avionics NAV 2000 Guía de instalación descargar pdf (Pagina 21)

SkyView System Installation Guide - Revision R 1-3

5. The EMS 37-pin Main Sensor Harness includes a 9-pin connector that is wired to pins 11

(Orange wire), 12 (Yellow wire), and 30 (Black wire). This connector is used for other

Dynon products, but is not used in SkyView installations. Thus, the 9-pin connector

should be removed to use these wires for connecting sensors to the SV-EMS-220.

Remove the connector by cutting the three wires close to the 9-pin connector.

6. SkyView SETUP MENU is accessed by pushing and holding Buttons 7+8 together for 2-3

seconds.

7. Setting the Tail Number is required for before you can configure your SkyView Network

(described below): SETUP > AIRCRAFT INFORMATION > TAIL NUMBER. If Tail Number

has not yet been issued for your plane, set TAIL NUMBER to something other than

DYNON.

8. Many SkyView displays and modules communicate over a common set of wires – the

SkyView Network that terminates at the D9 connectors on the back of your SkyView

display(s). Getting all modules and displays “talking” on SkyView Network is done by

going to SETUP MENU > SYSTEM SETUP > NETWORK SETUP > CONFIGURE > (click right

one more time). If a module is noted as “requires update”, press the UPDATE button.

Otherwise, press the FINISH button. Note that you will not see any flight instruments or

engine instruments before a network configuration is performed, even if the SV-

ADAHRS-200/201 and SV-EMS-220/221 have been wired properly and are connected.

9. Devices that do not utilize SkyView Network are connected via serial port connections.

Dynon devices that use serial ports include the SV-ADSB-470, SV-GPS-250, SV-XPNDR-

261/262, and various third-party devices. As serial devices are not part of the SkyView

Network, they will not be seen on the list of devices seen as you configure SkyView

Network above. Instead, configuring SkyView to communicate with SV-GPS-250 and SV-

XPNDR-261/262 is done via a more manual process in SETUP MENU > SYSTEM SETUP >

SERIAL PORT SETUP.

10. If you have installed an SV-GPS-250, its SERIAL IN FUNCTION must be set to POS 1.

11. After you’ve configured SkyView Network, have properly configured any serial devices,

exit the Setup Menu. Your SkyView display should now display EMS, PFD, and MAP. Map

will not display without a GPS fix (the airplane symbol on the Map page will also flash

with “?” if it does not have a GPS fix.

12. Your SkyView may require various updates such as system software, databases, and

Sensor Definitions. See

http://www.dynonavionics.com/docs/support_software_SkyView.html for more details

on the updates available for SkyView. If you are a non-US customer, the display of

aviation and obstacle data on your SkyView system requires a database purchase from

Jeppesen or PocketFMS. Note that firmware on each SkyView display must be updated

individually.

13. Common issues for setting up SkyView engine monitoring:

a. The configuration of sensors installed on SkyView at the factory is generic;

therefore “Red X’s” on the EMS for various sensors are normal until sensor

configuration for your particular engine sensor configuration is complete.

b. The layout of which sensor “widgets” are shown on the screen, sizes, styles, etc.

is completely configurable: SETUP > EMS SETUP > SCREEN LAYOUT EDITOR

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 400 401

Comentarios a estos manuales

Sin comentarios

VAL Avionics NAV 2000 Guía de instalación Pagina 21

Comentarios a estos manuales